ARTIST SERIES SHC-200

RECOMMENDED USES









New from JJB-Electronics comes the SHC-200! We have been
asked for the past few years when we were planning to offer a
discreet soundhole mounted volume and tone control option.
The wait is over! This system is great for people who would like
these controls close at hand, but do not want to drill holes in
their instrument to mount conventional potentiometers.

We didn't compromise on this system one bit. Everything that
went into it is the absolute best we could find, right down to the
premium connectors. The board is a very high quality, double-
layer design. This cuts down on the possibility of feedback or
other unwanted harmonic noises. The control board is mounted
to the soundboard using a very strong 3M double-stick material.

It was very important to us while developing this system that
there would be a retrofit option for people with existing JJB-
ELECTRONICS systems installed. Please take a look at the pic on
the right. No soldering is required to retrofit this system to your
current one. Just plug in a few connectors and you're good to
go! This option can be selected from the drop-down menu on
the right.

This system features 100% passive circuitry, because we firmly
believe that batteries have no place inside of an acoustic
instrument. This also helps to make it a very reliable system.

These are built using very high quality 15 or 20mm transducers.
Please select the desired size from the drop-down menu above.
The 15mm configuration is designed for guitars which do not
provide enough space on the bridgeplate to allow for the bigger
sized piezo's. These are ideal for guitars with more mid-range
and bass response. They are designed for more resonant
guitars or ones with thinner soundboards.
.Both systems have a
very similar tone but the smaller system provides a little less
output than the bigger sized system. In many cases this slight
difference is negated by the higher resonance of a smaller
bridgeplate. The 20mm size is the best option for 12 string
guitars as well as high-string setups. Either size can be used
with or without a preamp with fantastic results.

It utilizes a triple surface transducer design. This results in a
very wide frequency range and very natural reproduction of
sound. The three-piezo configuration offers a few advantages
over single and double piezo systems. Having three piezo’s
affords you the opportunity to place them at three different
points on the soundboard thus resulting in an improved
dynamic range due to the fact that they transmit the resonance
found at more than one point. These special surface
transducers are under less pressure than under saddle pickups
thus decreasing the likelihood of them transmitting a
percussive or harsh sound. Each piezo is designed to pick up a
string pair as well as the resonance found in a significant
amount of the soundboard. These do not fade or distort at high
volume or with high-power systems. The highs are crystal clear
while the lows are what they should be, low! This pickup
configuration is offered in several high end guitars.

All of our products feature quality components and
construction. These utilize a premium quality Switchcraft 1/4”
nickel plated stereo end-pin jack. This system will give you a
very clean install for those who do not want to compromise the
integrity of their beloved instrument. The end-pin jack also
doubles as a strap button. These, like all of our systems, can be
installed in about 15 minutes! They are a very simple and
inexpensive means of turning your acoustic instruments in to
acoustic electric.
Several of you may be wondering,
"so how does it sound". Please click
here to check out our new
customer-submitted sound clip page
for a demo.
15MM PIEZO SHC-200
20MM PIEZO SHC-200
Steel string guitars with more
resonant tops. This generally
includes all solid top guitars
Guitars with laminate tops,
since they are generally less
resonant than solid tops
Travel / Parlor guitars. (It is
recommended that you check
the dimensions to ensure it will
fit using the diagram below.
12 string guitars
  5 string acoustic bass guitars
Click here to view the installation
instruction document
AS REAL AS IT GETS
MADE WITH PRIDE IN
THE USA
Available options
Retrofit Option
Already have a JJB-ELECTRONICS system installed in your
guitar? Don't worry, we didn't forget about you! The pic
below and to the left are of our SHC-200 retrofit option.
No soldering is required. Just plug and play! This option
can be selected from the drop-down menu above.
Currently Unavailable.
Please check back soon!